10KV無線測溫裝置產品介紹

1 安裝使用指南

1 Installation Guide

1.1 產品概述

1.1 Product Introduction

10KV無線測溫裝置根據《NB/T 42086-2016無線測溫裝置技術要求》開發，可用于3~35kV戶內開關柜，包括中置柜、手車柜、固定柜、環網柜等多種開關柜，也可用于0.4kV低壓柜，包括固定柜，抽屜柜等。無線溫度傳感器可安裝于柜內任何發熱點上，利用無線數據傳輸技術，可實時把監測數據發送出去，通過ARTM-Pn無線測溫采集裝置就地顯示溫度，也可以通過裝置的RS485接口互聯組網實現遠程智能監控。

ARTM-Pn wireless temperature measuring equipment has been developed in compliance with Specification for Wireless Temperature Measuring equipment, NB/T 42086-2016. It is suitable for 3-35kV indoor switchgears, including built-in switchgears, handcart switchgears, fixed switchgears and loop-net switchgears. It is also suitable for 0.4kV low-voltage switchgears such as fixed switchgears and drawer switchgears. The wireless temperature sensors can be installed at any heating point in switchgears, the device utilizes the wireless data transmission technology for real-time transmission of monitored temperature data and displays such data on ARTM-Pn locally. In addition, it can be networked via the RS485 port for remote intelligent monitoring.

1.4 產品安裝

1.4 Product Installation

10KV無線測溫裝置采用面板嵌入式安裝，首先柜體盤面上制作規定尺寸的正方形槽孔，裝置取下支架后嵌入槽孔，再將支架推入卡槽鎖緊即可。

ARTM-Pn wireless temperature measuring equipment is installed with the front panel embedded. First, make a square hole on the switchgear surface to the specified size. Then, separate the two brackets from device and embed the device into the square hole. Finally, push and lock the brackets.

1.4.1 安裝方法

1.4.1 Installation Method

1.4.2 開孔尺寸

1.4.2 Hole Size

1.4.3 無線溫度收發器的安裝

1.4.3 Wireless Temperature Coordinator Installation

與ARTM-Pn產品配套使用的無線溫度收發器直接安裝在ARTM-Pn 的無線測溫接口（61~64），并連接好天線；產品尺寸外觀和安裝效果如下圖所示。

The wireless temperature transceiver used with ARTM-Pn product is directly installed in the wireless temperature measuring interface of ARTM-Pn (61~64), and the antenna is connected. Product size, appearance and installation effect are shown in the following picture.

1.4.4 無線溫度傳感器的安裝

1.4.4 Wireless Temperature Sensor Installation

無線溫度傳感器共有多種型號，分別對應磁吸固定、表帶固定、合金片固定等安裝方式。

There are several types of wireless temperature sensors and mounting methods correspondingly, i.e. magnetic , belt and alloy chip fixing.

1.4.4 10KV無線測溫裝置的安裝

1.4.4 Wireless Temperature Sensor Installation

無線溫度傳感器共有多種型號，分別對應磁吸固定、表帶固定、合金片固定等安裝方式。

There are several types of wireless temperature sensors and mounting methods correspondingly, i.e. magnetic , belt and alloy chip fixing.

2常見故障的診斷分析與排除方法

2The Analysis and Solvent of Some Faults

2.1 輔助電源故障

2.1 Power Source Fault

裝置接通輔助電源后屏幕不亮？

The LCD does not work after the device power on?

可能原因：外接端子線序錯誤。

Reason: Wiring connector connects to power source wrong.

處理方法：拔出“無線測溫”接口處的外接模塊，檢查電源端口，重新上電裝置判斷。

Solvent：Take off the connector of “Wireless Temp”, check up the power source connector, and power

on it again.

2.2 告警繼電器動作故障

2.2 Relay Output Fault

無線測溫節點溫度定值越限而繼電器不動作？

When measured wireless temperature values exceed the setting values, the relay output does not work?

可能原因：相應的控制字未投入。

   Reason: “Node Enable” is not “ON”.

處理方法：“主菜單”—>“定值”菜單將相應的控制字設置為投入。

2.3 通信故障

2.3 Communication Fault

上位機或后臺軟件與裝置通信錯誤？

   PC /host computer can’t communicate with the device?

可能原因：裝置地址或串口參數設置錯誤。

Reason: The address or other port parameter of communication is wrong.

處理方法：“主菜單”—>“通信”設置正確的裝置地址或串口參數。

Solvent: “MENU”->”Comm”, Set valid address or other port parameter.

2.4 節點溫度值顯示故障

2.4 Wireless Temperature Fault

“節溫”菜單無溫度值顯示或無某一路溫度值顯示？

   On the “Temp” interface, the device shows “No Nodes ”?

可能原因：傳感器電池開關未打開或未啟動，傳感器不配對。

Reason: Active wireless temperature sensor battery is closed or passive wireless temperature sensor does not work, or the sensor is not matched to the device.

處理方法：（1）查看無線溫度傳感器的電池開關是否撥到“ON”端？（電池開關從OFF端撥到ON端后，無線溫度傳感器上的綠燈亮滅閃爍2次表示開關接通正常，否則等待5s后重撥）；查看無源測溫傳感器相應回路是否正常運行，且電流5A以上。

Solvent: (1) Check up the active wireless temperature whether its battery switch is “ON”? (When the battery switch turn to ON from OFF, the green light will lighting twice, it is worked, otherwise, wait for 5s and turn on it again); check up the circuit whether it worked with the current above 5A.

（2）查看裝置上的條碼與無線溫度傳感器上的條碼是否一致，不一致時找到對應的無線溫度傳感器更換或重新配對無線溫度傳感器（詳見本說明書2.3章節下的“節溫設置”）。

(2) Check up the bar code on wireless temperature sensor and device, if they are not same, find out the sensors with same bar code or bind the sensors online (the detailed method is at “Sensor Setting” in chapter 2.3).